Delayed or instant concrete release agent
 |
CoV content 0% |
 |
Carbon FOOTPRINT® |
.jpg){kind=logo}
 |
|
ALL TYPES OF PANELS
and FORMWORK
Rough, varnished and planed Bakelite-coated wood, plywood.
Steel and aluminium.
Plastics, ABS, PVC, Polyesters, Polyurethanes.
ALL TYPES OF CONCRETE
including architectural and self-placing concretes.
Compatible with all hydraulic binders,
adjuvants and additives
No bubbling, anti-powder additive.
For smooth facings.
Non-staining.
Repels dirt from panels.
Does not alter the adhesion of plaster, rendering or paint.
WIDE TEMPERATURE RANGE
Freezing point
- 8°C
Fully resistant to temperature variations,
applicable from 0°C to 90°C.
Can be used on thermal panels during steam curing.
NO DANGER PICTOGRAM
ZERO RISK 100% SAFE
Not dangerous to humans and the environment.
Solvent-free, volatile organic compound-free.
No danger pictograms.
No risk phrases.
No exposure limit values or time-weighted average
(ELV - TWA).
No risk of irritating, chapping or drying out the skin.
LOW CONSUMPTION
Absorbent formwork
1 L for 60 m2
Non-absorbent formwork
1 L for 80 m2
| Download the datasheet |
PHYSICAL AND CHEMICAL PROPERTIES
CLASSIFICATION : NON-POLAR AGRO-BASED FLUID
|
PROPERTIES |
VALUES |
UNITS |
|
Appearance |
Clear |
- |
|
Colour |
Orange-yellow |
- |
|
Odour |
Light, characteristic |
- |
|
Density at 25°C |
0.894 |
kg/m3 |
|
Freezing point |
-20 |
°C |
|
Solubility in water |
0 |
% |
|
Kinematic viscosity at 40°C |
10.5 |
mm²/s |
|
Surface tension |
32 |
Dynes/cm |
|
Refractive index |
1.4620 |
|
|
Solvent power - Kauri Butanol index |
>200 |
- |
|
Acid value |
<1 |
mg(KOH)/g |
|
Iodine value |
<120 |
gI2/100g |
|
Water content |
< 0.2 |
% |
|
FIRE SAFETY PROPERTIES |
||
|
PROPERTIES |
VALUES |
UNITS |
|
Flash point (vacuum) |
>170 |
°C |
|
Self-ignition point |
>250 |
°C |
|
Lower explosive limit |
Non-explosive |
% (by volume) |
|
Upper explosive limit |
Non-explosive |
% (by volume) |
|
Content of explosive, oxidising, flammable, highly or extremely flammable substances |
Total absence |
% |
|
ENVIRONMENTAL PROPERTIES |
||
|
PROPERTIES |
VALUES |
UNITS |
|
Anisidine value |
<5 |
- |
|
Peroxide value |
<10 |
meq(O2)/kg |
|
TOTOX (anisidine value + 2x peroxide value) |
<25 |
- |
|
CMR, irritating and corrosive substance content |
Total absence |
% |
|
Residual methanol content from transesterification |
0 |
% |
|
Emissions of hazardous, CMR, irritant, corrosive compounds at 160°C. |
0 |
% |
|
Exposure limit value and time-weighted average (ELV and TWA) |
Without |
ppm |
|
ENVIRONMENTAL PROPERTIES |
||
|
PROPERTIES |
VALUES |
UNITS |
|
Water endangering |
1 |
class |
|
Primary biodegradability CEC 21 days at 25°C |
over 90 |
% |
|
Easy biodegradability OECD 301 A over 28 days |
over 80 |
% |
|
Easy and ultimate biodegradability OECD 310 C over 28 days Biodegradation at 67 days |
over 90 100 |
% % |
|
Bioaccumulation n-octanol water partition coefficient |
less than 3 |
log Kow |
|
Vapour pressure at 20°C |
<0.1 |
hPa |
|
VOC (Volatile Organic Compounds) content |
0 |
% |
|
Solvent content |
0 |
% |
|
Environmentally hazardous substances content |
Total absence |
% |
|
Content of compounds with a GWP |
0 |
% |
|
Content of compounds with an ODP |
0 |
% |
|
Carbon balance, life cycle analysis |
1.55 |
Carbon Equivalent Kg |
INSTRUCTIONS AND PRECAUTIONS FOR USE
SOLVETAL HDB 600 aids mould release by removing concrete/formwork adhesion.
It has 2 actions
Physical action: creates a non-stick oily layer between the two substrates
Chemical action: saponification by the reaction of a strong base (the cement) with a fatty acid (the product).
To optimise results, apply to clean panels that are free from corrosion or residual traces of cement.
SOLVETAL HDB 600 does not create corrosion on steel panels.
New wooden formwork should be treated with slurry before first use, to remove any xylose on the surface.
Spray sparingly on clean surfaces (3 to 5 bar pressure) or use a cloth, brush or squeegee (ensure there is no excess).
Also apply to the edges of the panels.
Concreting can take place immediately after application of the concrete release agent.
Do not apply to frameworks.
Never use or mix with waste oil or diesel fuel, which are extremely dangerous to users (H351 Carcinogenicity cat. 2)
PRÉSENTATION
|
Drum 200 L
|
Can 20 L
|
Manufacturing, lubrification, cleansing, protection,
IBiotec® Tec Industries® Service
offers a wide range of products reserved for industrial area
If you wish for :
a free sample
a technical advice
a product data sheet
a safety data sheet
IBiotec® Tec Industries®Service
manufacturer of technical chemical products.
Welcome to our website.
IBiotec® Tec Industries®Service is on : 